Home Products About Us Sales Network F.A.Q Contact us Info Center
Home > Products > Safety Harness & Safety Belt > Full Body Safety Harness >

Wristrong Catalouge

Wristrong facebook page   Wristrong Linkedin page   Wristrong Google+ Page

DX-211 Safety harness-Fall Protection Harness

Material:Polyester+Alumium+Steel
Safety Factor:N/M
Length:Universal
Color:Yelow/black
Standard: EN361,EN 362,EN 354,EN 355
Characteristic:Light weighted,CE approved
Package:Poly bags+carton boxes
 

Safety harness-Fall Protection Harness-DX-211-Economic but wearable and safe use


Hangzhou Wristrong Industry Co.,Ltd started to produce Full body safety harness and its accessories
6 years ago, when our partner in Taiwan joined us to develop the high quality safety harness for
Taiwan and international market. All of our safety harnesses are produced 100% according to Europe
EN361:358 2002 and Taiwan CNS, 
as well as EN 354 Safety Lanyard, EN 355 Energy Absorber, EN 362
connector,etc.

All of our webbing belts for safety harness are produced and quality checked by ourselves in house;
most of hardware are supplied from our
 Taiwan partner, which gurrantee the quality and
stablity.

 

DX-211 One point Full Body Safety Harness with height adjustable chest belt Specification

Extra D rings attached on chest belt for hanging tools,strong PE connecting buckles on chest belt

to realize the chest belt height.adjustable

 

 

Webbing Material                    

1500D/3300D Polyester Yarn           

Webbing Width

45mm-50mm

Color

Orange/Black/Optional

Size

Universal

Hardware Material

Heat Treated Alloy Steel

Load Capacity

150kgs/350lb

Tensile Strength

2230kgs/5000lb

Chest belts

Lenght Adjustable, by the Pass-thru buckle , Height Adjustable, by strong PE connecting buckles,extra D rings attached for tool hangling,easy to handle

Dorsal belts

Fixed with one stamped alloy steel D-RING

Shoulder belts

Adjustable, by one alloy steel buckle attached on each side

Thigh belts

Adjustable, by one Pass-thru buckle on each side

Seat belts

pecial designed shape to make workers falling into sitting position , ease the Pressure on limbs

Waist Belts

None

Waist Strap Buckles

None

Application

Construction, confined space, electrician height tower working

Standard

CE EN361 CNS

Feature

Simple easy to use, economic price with stable quality

 

Specified Photos for the DX-211 Full body safety harness

 

Different Models of Full Body Safety Harness and safety belts available 



Lanyards and Energy absorbers avaialbe for full body safety harness



DIFFERENT HARDWARE AVAILABLE FOR THE FULL BODY SAFETY HARNESS


How to inspect and maintain personal fall arrest systems


Fall Protection Harness (and body belt) inspection:
 
To inspect your harness or body belt, perform the following procedures.
1) Webbing – Grasp the webbing with your hands 6 inches (152 mm) to 8 inches (203 mm) apart. Bend the webbing in an inverted “U”. The surface tension resulting makes damaged fibers or cuts easier to detect. Follow this procedure the entire length of the webbing, inspecting both sides of each strap. Look for frayed edges, broken fibers, pulled stitches, cuts, burns and chemical damage.
2)  D-Rings/Back Pads – Check D-rings for distortion, cracks, breaks and rough or sharp edges. The D-ring should pivot freely. D-ring back pads should also be inspected for damage.
3) Attachment of Buckles – Inspect for any unusual wear, frayed or cut fibers, or broken stitching of the buckle or D-ring attachments.
4) Tongue/Grommets – The tongue receives heavy wear from repeated buckling and unbuckling. Inspect for loose, distorted or broken grommets. Webbing should not have additional punched holes.
5) Tongue Buckles – Buckle tongues should be free of distortion in shape and motion. They should overlap the buckle frame and move freely back and forth in their socket. Roller should turn freely on frame. Check for distortion or sharp edges.
6) Friction and Mating Buckles – Inspect the buckle for distortion. The outer bars and center bars must be straight. Pay special attention to corners and attachment points at the center bar.
7) Quick-Connect Buckles – Inspect the buckle for distortion. The outer bars and center bars must be straight. Make sure dual-tab release mechanism is free of debris and engages properly.
 
Safety Lanyard inspection
 
When inspecting lanyards, begin at one end and work to the opposite end, slowly rotating the lanyard so that the entire circumference is checked. Additionally, follow the procedures below.
 
1) Hardware –
a) Snaps: Inspect closely for hook and eye distortions, cracks, corrosion or pitted surfaces. The keeper (latch) should seat into the nose without binding and should not be distorted or obstructed. The keeper spring should exert sufficient force to firmly close the keeper. Keeper locks must prevent the keeper from opening when the keeper closes.
b) Thimbles: The thimble must be firmly seated in the eye of the splice, and the splice should have no loose or cut strands. The edges of the thimble must be free of sharp edges, distortion or cracks.
2) Wire Rope Lanyard – While rotating the wire rope lanyard, watch for cuts, frayed areas, or unusual wearing patterns on the wire. Broken strands will separate from the body of the lanyard.
3) Web Lanyard – While bending webbing over a pipe or mandrel, observe each side of the webbed lanyard. This will reveal any cuts or breaks. Swelling, discoloration, cracks and charring are obvious signs of chemical or heat damage. Observe closely for any breaks in stitching.
4) Rope Lanyard – Rotate the rope lanyard while inspecting from end-to-end for any fuzzy, worn, broken or cut fibers. Weakened areas from extreme loads will appear as a noticeable change in original diameter. The rope diameter should be uniform throughout, following a short break-in period.
5) Shock Absorber Pack – The outer portion of the pack should be examined for burn holes and tears. Stitching on areas where the pack is sewn to D-rings, belts or lanyards should be examined for loose strands, rips and deterioration.
6) Shock-Absorbing Lanyard – Shock- absorbing lanyards should be examined as a web lanyard (described in item 3 above). However, also look for the warning flag or signs of deployment. If the flag has been activated, remove this shock-absorbing lanyard from service.
 
Self-Retracting Lifeline Inspection
 
1) Check Housing – Before every use, inspect the unit’s housing for loose fasteners and bent, cracked, distorted, worn, malfunctioning or damaged parts.
2) Lifeline – Test the lifeline retraction and tension by pulling out several feet of the lifeline and allow it to retract back into the unit. Always maintain a light tension on the lifeline as it retracts. The lifeline should pull out freely and retract all the way back into the unit. Do not use the unit if the lifeline does not retract. The lifeline must be checked regularly for signs of damage. Inspect for cuts, burns, corrosion, kinks, frays or worn areas. Inspect any sewing (web lifelines) for loose, broken or damaged stitching.
3) Braking Mechanism – The braking mechanism must be tested by grasping the lifeline above the impact indicator and applying a sharp steady pull downward which will engage the brakes. There should be no slippage of the lifeline while the brakes are engaged, once tension is released, the brakes will disengage and the unit will return to the retractable mode. Do not use the unit if the brakes do not engage. Check the hardware as directed in the previous section, Lanyard Inspection — Hardware/Snaps. The snap hook load indicator is located in the swivel of the snap hook. The swivel eye will elongate and expose a red area when subjected to fall arresting forces. Do not use the unit if the load impact indicator has been activated.
Cleaning
Basic care of all safety equipment will prolong the durable life of the unit and will contribute toward the performance of its vital safety function. Proper storage and maintenance after use are as important as cleansing the equipment of dirt, corrosives or contaminants. Storage areas should be clean, dry and free of exposure to fumes or corrosive elements.
1) Nylon or Polyester – Remove all surface dirt with a sponge dampened in plain water. Squeeze the sponge dry. Dip the sponge in a mild solution of water and commercial soap or detergent. Work up a thick lather with a vigorous back and forth motion; then wipe with a clean cloth. Hang freely to dry, but away from excessive heat.
2) Housing – Periodically clean the unit using a damp cloth and mild detergent. Towel dry.
3) Drying – Equipment should dry thoroughly without close exposure to heat, steam or long periods of sunlight.
 
Following a strict and systematic inspection and maintenance program for personal fall arrest systems may necessitate removing a harness or lanyard from service prior to the expiration of its stated life expectancy guideline. When doing so, for safety’s sake, the product should be disposed of in a manner that prevents inadvertent further use.
In the end, it is ultimately the responsibility of the user of a personal fall protection system, or any personal protection equipment, to determine if the item suitable for use — and to keep them safe and injury free.